Scans made with the OpenPlan3D iPhone app record walls, doors, windows and furniture, not the ceiling. Both 3D views show your rooms open at the top like a dollhouse:
On iPhone: on the scan's review screen, switch to 3D and drag upward to tilt the view and look down into the rooms.
In the web editor: click 3D at the top, then drag to orbit and scroll to zoom. Top-Down View (top right of the 3D view) looks straight down, and Make Walls Transparent lets you see through the walls.
If something still covers your rooms, it's usually one of these:
Another floor is on top. With Show All Floors Stacked on, the floors above the one you're editing are drawn too, and with Other floors set to Solid they hide it. Set Other floors to Translucent, or switch back to Active Floor Only.
It's a mesh scan from another app. Apps that capture a textured 3D mesh record everything the camera saw, including the ceiling, and OpenPlan3D can't cut a ceiling out of an imported 3D model. Scan the rooms with the OpenPlan3D app's Start Scanning instead, or trim the ceiling off in the app that made the mesh.
The camera is inside a room. If you zoom in until the camera is below ceiling height, you see the room's ceiling from underneath. Zoom out, or use Top-Down View.
The iPhone app scans one floor at a time: walk one floor, tap Finish, then start a new scan for the next floor. You don't need to scan the stairs.
Separate scans are all you need for a 2D floor plan of each level.
One plan with several floors gives you a 3D model of the whole house, with each floor at its real height and stairs between them. Build it in the web editor, as described in the next answer.
Open one floor's scan, such as the main level, in the web editor with Send to OpenPlan3D on the iPhone. It becomes the plan's Ground Floor.
Add the other floors. Click + next to the floor name at the top of the editor. Choose Empty floor under Add Top Floor for each level above, or under Add Floor Below for each level underneath, such as a basement. To give a floor your own name, click the pencil next to the floor name.
Export the other scans from the iPhone. For each other floor's scan, tap Export on its review screen, choose Export Editable Plan (JSON), and save or AirDrop the file to your computer.
Import each scan onto its floor. In the editor's Build panel, click Import RoomPlan and choose the file. Select Add to this plan, pick the floor it belongs on under Floor, and click Import.
Line it up. The scan arrives selected, so drag or rotate it into place. To see the floor below as a guide while you do, open Layers at the bottom of the 2D plan and turn on Floor Below.
Set each floor's height, as described in the next answer.
If a scan ends up on the wrong floor, move it instead of importing it again.
Select it: click an item, drag a box around several, or press Ctrl+A (⌘A on a Mac) to select everything on the floor. A scan you just imported is already selected.
Move it: click the layers button in the toolbar above the selection and choose Move to the floor you want. The editor switches to that floor with the moved items still selected.
Everything keeps its exact position, so walls stay lined up with the floors above and below:
Walls take their doors and windows with them.
A named room moves when all of its walls do.
Undo puts everything back in one step.
The button only appears when the plan has more than one floor.
Click the gear icon at the top of the editor to open Settings, then the Project tab. Under Floor elevations, enter each floor's height above ground in centimetres (1 ft ≈ 30.5 cm). Floors start 300 cm apart.
A basement added with Add Floor Below starts 300 cm under the lowest floor, so at −300 under a ground floor at 0. Change it to your real depth, for example −280.
Floors keep their order: Add Floor Below goes under the lowest floor and Add Top Floor goes above the highest. Keep each floor's elevation higher than the one below it.
A good way to measure: count the steps between two floors and multiply by the step height. That's usually about 18 cm (7 in), so 15 steps is about 270 cm.
Treat each level you can stand on as its own floor, and name each one with the pencil next to the floor name. For example, a daylight basement, a front entry halfway up, and an upstairs living area become three floors:
Basement: at elevation 0.
Entry: at about 140 cm, or wherever your steps say.
Upstairs: at about 280 cm.
A small level like an entry can be just its own walls. On the entry floor, add one stair going Up to the living area and one going Down to the basement. Each stair automatically reaches the floor it leads to (see the next section).
Place it: in the Build panel, choose Add Stairs and click the plan where the stairs start.
Set it up: select the stairs to open Stair Properties. Choose the shape (Straight, L-Shaped, U-Shaped or Spiral) and the number of Risers, then drag and rotate the stairs into place.
Pick a direction: an Up stair climbs from its floor to the next floor above. A Down stair descends from its floor to the floor below. You don't set a height: the stairs span the gap between the two floors' elevations.
You only need each flight once, on the floor at either end. If your plans show it on both floors (Up below, Down above, in the same spot), the two line up as one flight in 3D.
A landing where the stairs turn: choose L-Shaped or U-Shaped in Stair Properties. The landing is part of the stair.
A landing you can walk off, such as an entry or a half-level between two floors: make it its own floor at its own elevation. Then add a stair from it up to the floor above and one down to the floor below, as in split-level houses.
Enclose the opening: on the upper floor, draw walls around the opening over the stairs. Lower their height in Wall Properties if you want railings instead of full walls.
Remove the floor: click inside that space to select the room, then turn on Open to floor below. This removes the floor there and leaves it out of the floor area.
Check it in 3D: click the layers button at the top right of the 3D view.
Show All Floors Stacked draws every floor at its height, with the stairs between them.
Active Floor Only shows the floor you're on, and you can still look down through the opening at the stairs below.
On iPhone, the same setting is in the room's properties: Open to floor below.